INTERIOR QUICK SOP

Follow these steps IN ORDER on every interior. Do not randomly bounce around the car.

1. Open every door + remove floor mats. Put mats somewhere clean. Collect obvious trash. Do not throw away anything that could belong to the customer. Keep their belongings together.

2. Move the front seats. Move them all the way back, then forward. Look underneath and between the seats. Check seat rails, underneath seats, center-console gaps, door pockets, rear floors, and trunk.

3. First vacuum — remove all loose dirt. Vacuum seats and seams first, then floors, under seats, between seats, rear floors, and trunk. Use a detailing brush while vacuuming cracks and tight areas. Do not start spraying chemicals on top of loose dirt.

4. Brush out cracks and crevices. Do vents, buttons, seams, cupholders, console gaps, seat rails, door pockets, and around trim. Brush the dirt toward the vacuum instead of spreading it around the car.

5. Clean carpets + floor mats. Vacuum thoroughly first. Lightly apply Carpet Bomber to dirty carpet/mats. Let it work briefly, then agitate. Drill brush is okay on durable carpet and mats. Do not soak the carpet. After agitation, wipe/blot the dirty solution out with clean microfiber towels.

Repeat only on areas that still need it. P&S lists Carpet Bomber for automotive carpet and upholstery and says it can be used stronger for heavy contamination or diluted for lighter cleaning.

6. Clean cloth seats. Vacuum seams first. Work one small section at a time. Lightly apply cleaner, gently agitate with microfiber or an appropriate soft brush, then blot/wipe the dirt out with clean microfiber towels. If the seat is becoming soaked, STOP adding chemical. We do not have extractors, so moisture control matters.

7. Leather / Alcantara / delicate fabric = Pol Star. Do not attack these with Carpet Bomber and a drill brush. Koch-Chemie specifically approves Pol Star for leather, Alcantara, upholstery, and textiles at 1:5–1:20 depending on contamination.

Apply lightly, gently work it with microfiber/sponge, then remove residue with a damp microfiber. Always test questionable material first.

8. Headliner = VERY LIGHT cleaning only. Never soak it. Never use the drill brush. Apply a small amount of appropriate cleaner to your microfiber instead of saturating the headliner. Gently blot/work the dirty area. If it is heavily stained, use the Headliner Guide rather than getting aggressive.

9. Clean dash + center console. Work from the top downward. Clean dashboard, steering-column area, console, gear-selector area, cupholders, buttons, and storage areas. Spray the towel/brush instead of blasting cleaner directly into switches, screens, or electronics.

10. Clean doors. Do the upper panel, armrest, handle, switches, speaker area, lower panel, door pocket, and door jambs. Door pockets and jambs are commonly missed, so physically check them before moving on.

11. Clean high-touch areas. Steering wheel, handles, buttons, gear selector, armrests, seatbelt buckles, cupholders. These often still feel greasy even when they look clean.

12. Use steam only when needed. Steam can help loosen grime in suitable hard surfaces and tight areas, but it is not a universal cleaner. Keep concentrated heat away from screens, electronics, delicate adhesives/materials, and anything you are unsure about. Use the Steamer Guide if you’re unsure.

13. Wipe every surface dry + inspect it. No puddled cleaner. No leftover foam. No greasy residue. No soaking-wet seats or carpet. Switch to clean microfiber towels when yours become dirty.

14. Apply protection only AFTER cleaning. PERL is for clean, dry interior plastic/vinyl/modern leather. CARPRO specifies 1:5 for interior/dash/leather; apply a thin layer and wipe evenly. APPLY ON FLOORMATS! Never apply dressing to pedals, steering wheel, glass, screens, or anything that could become slippery.

15. Interior glass LAST. Clean windshield, side windows, rear glass, mirrors, and glass roof if included. Lower windows slightly and clean the upper edge. Look at the glass from multiple angles. No streaks.

16. Final vacuum. Vacuum again because brushing/wiping knocks debris back onto the floor. Check under seats again, seat seams, around rails, rear floors, mats, and trunk.

20. Final interior inspection. Before Final QC, physically check: driver floor, passenger floor, rear floors, under seats, seat rails, between seats, seats/seams, cupholders, console, dashboard, vents, doors/pockets, jambs, glass, trunk, and customer belongings.

If you see something dirty, fix it before taking after photos.